NEW REPUBLIC LAGUN MVM-2

SPECIFICATIONS:

Table:
Table size ----------------------------- 50 inch x 10 inch
T-slots -------------------------------- 3 on 2 1/2 inch
centers
T-slot size ---------------------------- 5/8 inch
Maximum weight on table ---------------- 661 lbs.
Travels:
Table travel X-axis, manual ------------ 35 inch
with power feed --- 32 inch
(Depending on power feed)
Cross travel, Y axis ------------------- 16 inch
Knee travel, Z axis -------------------- 16 inch
Ram travel ----------------------------- 22.04 inch
Head:
Main motor ----------------------------- 3 HP
Mechanical Infinite variable speed with
(High-Low) manual settings (60 HZ) ------ 60 to 4500 RPM.
Low (60 to 500
rpm)
------ High (500 to 4500
rpm).(Opt.
Electronic
Variable
Speed- 0 to 5000)
Head swivel (Left to right) ------------ 45??
Head tilt ------------------------------ 45??
Distance, spindle to column ------------ 6.25 inch to 28 inch
Distance, spindle to table ------------ 4 to 20 inch
Quill:
Power quill feeds ---------------------- .0015, .003,
.006 in./rev
Spindle taper -------------------------- R-8 (Opt. #40
NST - #30 NST
Quill diameter ------------------------- 3.375 inch
Quill travel --------------------------- 5 inch
Machine Constructive Dimensions:
Column turret diameter (graduated) ----- 15 inch
Knee width ----------------------------- 13.77 inch
Knee to column bearing length ---------- 31.49 inch
Saddle & table bearing length ---------- 20.07 inch
Ram & turret bearing length ------------ 17.71 inch
Ram length ----------------------------- 32.82 inch
Physical:
Weight --------------------------------- 2,645 lbs.
Height --------------------------------- 83.46 inch
Width ---------------------------------- 65.59 inch
Depth ---------------------------------- 78.11 inch
Power, Dual Voltage Motors ------------- 230/440 Volts

EQUIPPED WITH:

??Spindle taper R-8
??Flood coolant system
??Hardened & Precision ground ways
??One shot lubrication system
??Draw bar
??Operators Manual/Parts List
??Basic Service Tool kit
??Way covers (rubber type)
??3/60/220/440 volt electrics. (Electric cord to be
hardwired to
the plant line power with disconnect.)
(See options for other electrical configurations
available.)

OPTIONAL FEATURES:

Head Options
5 HP EVS HEAD, 0-4500 RPM, 220V -------------------- $4,150
Transformer for voltage 440 or 480V ---------------- $4,150

Power Feed Options
Lagun Lighting X-Axis Longitudinal power feed - 110V $915
Lagun Lighting Y-Axis Cross power feed - 110V ----- $915
Lagun Lighting Z-Axis Vertical knee lift - 110V ---- $915
Servo #140 X-Power Feed (Longitudinal) - 110V ------ $1,235
Servo #150 X-Power Feed (Longitudinal) - 110V - XHD $1,420
Servo #140 Y-Power Feed (Cross) - 110V ------------- $1,245
Servo #150 Y-Power Feed (Cross) - 110V - XHD ------- $1,370
Servo #140 Z Power Feed (Knee Lift) - 110V -------- $1,300
Z Axis Power Feed (Type 200) ----------------------- $1,360
Extension kit (adds 3 inch lost by power feed on X) (servo
only) ---------------------------------------------- $690

Digital Read Outs* (Installed Prices)
2 axis Newall DP700 System 16 X 36 ----------------- $2,452
3 axis Newall DP700 system - w/Quill 16 X 36 X 5 --- $3,299
3 axis Newall DP700 system - w/ Knee 16 X 36 X 16 -- $3,299
2 axis Acu-Rite 200S 16 x 36 (Installed) ----------- $2,693
3 axis Acu-Rite 200S - w/ Quill 16 x 36 x 5 ------- $3,457
3 axis Acu-Rite 200S - w/ Knee 16 x 36 x 16 -------- $3,578
Quill Mounted Inch/Metric Digital Scale ------------ $600
Fagor/Acu-Rite Vue/300 Models available upon request.

Options
Power draw bar, use with standard draw bar Pneumatic $920
Lagun 6 inch angle lock swivel base vise , 8 inch opening -- $660
Kurt 6 inch D688 Anglock vise, Opens 8.8 inch -------------- $1,385
Swivel base for Kurt 6 inch vise ----------------------- $925
Halogen work light, 110V plug-in, 3ph, 60 Hz ------- $275
Clamp kit and Stud set (52 pc 5/8 inch T slots) -------- $200
Spindle Safety Guard with micro switch. (Note: When machine
is supplied with optional electric box.) ----------- $890
Set R-8 collets (11) 1/8 inch to ?? inch -------------------- $435
Collet rack for R-8 collets - 48 pcs. -------------- $130
Collet rack for R-8 collets - 16 pcs. -------------- $90
?? inch Drill chuck (Key type) w/R-8 shank -------------- $345
5/8 inch Drill chuck (Key type) w/R-8 shank ----------- $390
?? inch Drill chuck (Key type) w/ #40 taper ------------- $520
5/8 inch Drill chuck (Key type) w/ #40 taper ----------- $560
Shell end mill adapter in R-8, ?? inch ------------------ $185
Shell end mill adapter in R-8, 1 inch ------------------ $195
Shell end mill adapter in R-8, 1 ?? inch ---------------- $245
Right angle attachment - R-8 ----------------------- $1,556
1 in arbor, 18-1/4 in long with bushings and R-8 ------ P.O.R.
1 set end mill holders R8 taper - 7pc - 1/8 inch, 1/4 inch, 3/8 inch,
1/2 inch, 5/8 inch, 3/4 inch, 1 inch ------------------------------- $950
Shell end mill adapter in #40 Taper, ?? inch ----------- $310
Shell end mill adapter in #40 Taper, 1 inch ----------- $310
Shell end mill adapter in #40 Taper, 1 ?? inch --------- $340
Right angle attachment - #40 Taper ----------------- $2,650
1 in arbor, 18-1/4 in long with bushings and #40 ------ P.O.R.
1 set end mill holders-#40 Taper - 7 pc - 1/8 inch, 1/4 inch, 3/8 inch,
1/2 inch, 5/8 inch, 3/4 inch, 1 inch ------------------------------- $2,385
Spindle #40 Taper w/ Bearings ---------------------- $1,495
Collet chuck 40T w/ set of 15 collets from 1/8 inch to 1 inch$920
#40 100TG collet chuck w/ 1 set of 8 metric collets to use
with 100TG collet chuck - 8 pc - 6mm, 8mm, 10mm, 12mm,
14mm,
16mm, 18mm, 20mm. ---------------------------- $1000
1 set of 8 collets- Metric to be used with collet chuck
100TG - size 6 to 20mm. ---------------------------- $540
Arbor Support -------------------------------------- $1,190
4 inch Riser Block ------------------------------------- $1,835
8 inch Riser Block ------------------------------------- $1,950
12 inch Riser Block ------------------------------------ $2,150
Base Chip Pan (standard size) ---------------------- $800
Mist coolant system -------------------------------- $1,405
Hardened & Ground Square Ways ---------------------- STD
Rotary table - 6 inch diameter horizontal/vertical with index
plates --------------------------------------------- $4,095
Rotary table - 10 inch diameter horizontal/vertical with index
plates --------------------------------------------- $5,465
Rotary table - 12 inch diameter horizontal/vertical ---- $5,900
Adjustable Tailstock for 10 inch table ----------------- $1,770
Adjustable Tailstock for 12 inch table ----------------- $1,770
Slotting mounting kit with no support on ram ------- $2,000
Slotting attachment, 4 inch stroke, ?? HP, 5/8 inch tool capacity
---------------------------------------------------- $5,100
Slotter tool kit, with 7 tools, and 3 bit holders -- P.O.R.
Precision ball screws for X & Y - 1-1/4 inch dia. Includes yoke
for X & Y, 2 each extensions, 2 each couplings and top
mount handles for X & Y (1 set) -------------------- P.O.R.
Auto lubrication system (recommended for precision ball
screws) -------------------------------------------- $1,650
Start up and Training, Per Day ( $150/hour plus travel and
expenses) (NET) ------------------------------------ P.O.R
***IMPORTANT!!!! It is a must to use one of the following
electrical options when purchasing more than one 110V
option. Sample: Machine plus X axis power feed plus: Y axis
P.F - or Light or DRO - etc.

Special Electrics
UL approved - NFPA-79 Electrics - Push buttons command on
the head - 4 plugs for future connection of DRO - Servo
feed - Enclosure NEMA 12 with main disconnect. (NET) $1,580
Single source Power to the machine (220 or 440volts) Main
Power Disconnect - NEMA enclosure w/ transformer to operate
machine high voltage (main motor & coolant), and (4) 110v
plug-ins (for power feed, etc.) - Coolant push buttons
ON/OFF - Emergency Stop. (NET) --------------------- $3,500

Single source Power to the machine (220 or 440volts) - (NO
Main Power disconnect) - NEMA enclosure w/ transformer to
operate machine high voltage (main motor & coolant), and
(4) 110v plug-ins (for power feed, etc.) (NET) ----- $872

Standard Packaging Options
Wood skid w/ machine wrapped in plastic. (NET) ----- $225
Wood skid w/ treated wood, machine treated with anti-rust
coat over all metal surfaces and wrapped in plastic. (NET)
---------------------------------------------------- $500

Completely enclosed wood crate (treated wood), machine
treated with anti-rust coat over all metal surfaces and
wrapped in thermal sealed foil bag. (NET) ---------- $1,600

DELIVERY: Subject to Stock