BELSHAW PLUNGERS, CYLINDERS AND ATTACHMENTS FOR TYPE B/F/N DEPOS

Plungers, Cylinders and Attachments for Type B/F/N Depositors...
Belshaw plungers are high-quality stainless steel manufactured to very close tolerances. Sizes are in 1/8" increments through the range shown in the table below. Size is obtained by measuring the diameter of the base of the plunger.
Cylinders
:
Cylinders (see example at below) are inserted into the base of the hopper. Every plunger must match a similar size cylinder. More than one plunger can be used with the same cylinder, provided all are the same size.
Depositor Types
Plungers, cylinders and attachments are identical for Type B and Type F. Type N plungers are similar but shorter, and NOT interchangeable with Type B/F.
Plunger selection guide
Both Type B/F and Type N plunger part numbers are listed below. Other plungers and a wider range of sizes can be made as "specials" (contact your distributor). For Old Fashion donuts, use a plain plunger.
Download Specs
Plain Plunger
Star Plunger
French Cake (std mix) or French Cruller (cruller mix)
Type B/F Plungers
Part No: 7SS
Range: 1-1/2" to 2"
Part No: 7SC-SS
Range: 1" to 2"
Part No: 7B-1009
Range: 1-1/2" to 2"
Type N Plungers
Part No: N-1007SS
Range: 1-1/2" to 2"
Part No: N-1007SSS
Range: 1-1/2" to 2"
Part No: N-1008SS
Range: 1-1/2" to 2"
Download Specs
Krinkle plunger
Ball plunger
(specify 1,2,3,4 or 5 holes)
Stick plunger
(1 or 2 slots)
Type B/F
Plungers
Part No: 7F-1004
Range: 1-1/2" to 2"
Part No: 7G-1000
Range: 1-1/2" to 2"
7H-1000 (1 slot)
7H-1001 (2 slots)
Range: 1-1/2" to 2"
Type N Plungers
Part No: N-1012SS
Range: 1-1/2" to 2"
Part No: N-1009BSS
Range: 1-1/2" to 2"
Part No: N-1009SS
Range: 1-1/2" to 2"
Cylinder Selection
Cylinders are inserted into the base of your Belshaw hopper. The plunger passes through the heavy duty,
precision-manufactured cylinder liner with a minimum of clearance to form cake donuts. After depositing
many thousands of donuts, friction gradually wears out the sleeve on the interior, to the point where you
need a new cylinder.
For all Belshaw depositors:
Each plunger you use must match a cylinder of the exact same size. For instance, you cannot use a 1-1/2" plunger with a 1-3/4" cylinder.
Several plungers may be used with one cylinder, provided all are the same size.
Cylinder - for Type B and F
A 1-3/4" plain plunger and cylinder is standard with Type B and Type F depositor. Type B and F cylinders are interchangeable, and any size will fit any Type B and Type F depositor.
When ordering cylinders, specify both part number and size.
35SSA - small bore, for plungers 1" to 1-3/4"
35SSB - large bore, for plungers 1-7/8", 2"
Cylinder - for Type N, large cylinder with with small bore
If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that although this cylinder has a slot, it does NOT penetrate to the steel liner on the inside.
Part Number
N-1035L-A for plungers 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2", 1-5/8", 1-3/4"
Cylinder - for Type N, large cylinder with with large bore
If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that this cylinder has a slot that penetrates to the steel liner on the inside.
Part Number
N-1035L-B for plungers 1-7/8", 2", 2-1/8", 2-1/4" only
Cylinder - for Type N, small cylinder with small bore, OBSOLETE
If you are ordering a replacement cylinder, compare the dimensions of your old cylinder to the diagram at left. Notice that this cylinder has a slot that penetrates to the steel liner on the inside.
Part Number
N-1035 - for plungers up to 1-3/4"
Belshaw plungers are high-quality stainless steel manufactured to very close tolerances. Sizes are in 1/8" increments through the range shown in the table below. Size is obtained by measuring the diameter of the base of the plunger.Cylinders:Cylinders (see example at below) are inserted into the base of the hopper. Every plunger must match a similar size cylinder. More than one plunger can be used with the same cylinder, provided all are the same size.
Depositor TypesPlungers, cylinders and attachments are identical for Type B and Type F. Type N plungers are similar but shorter, and NOT interchangeable with Type B/F.Plunger selection guideBoth Type B/F and Type N plunger part numbers are listed below. Other plungers and a wider range of sizes can be made as "specials" (contact your distributor). For Old Fashion donuts, use a plain plunger.
Download Specs
Type B/F Plungers
Cylinder SelectionCylinders are inserted into the base of your Belshaw hopper. The plunger passes through the heavy duty,precision-manufactured cylinder liner with a minimum of clearance to form cake donuts. After depositingmany thousands of donuts, friction gradually wears out the sleeve on the interior, to the point where you need a new cylinder.For all Belshaw depositors:Each plunger you use must match a cylinder of the exact same size. For instance, you cannot use a 1-1/2" plunger with a 1-3/4" cylinder.Several plungers may be used with one cylinder, provided all are the same size.