NEW 2025 SHARP LMV-49-SMD

SHARP NEW MODEL LMV-49-SMD, Servo Motor driven Spindle (Hi/Low transmission gear eliminated)

• 3HP Motor
• Digital Variable Speed Drive
• R-8 Spindle
• Meehanite Casting
• Chromed Ways
• Self-lubricating motor Shaft Extends Pulley Life
• Abec-7 Super Precision Spindle Bearings

Capacity Inch Metric
Table Size 9 x 49 in. 230 x 1244 mm
T-slots (No., Size, Pitch) 3, 5/8, 2.5 in. 3, 16, 63.5 mm
Table Travel : X Longitudinal 36.6 in. 929 mm
Table travel : Y Cross 12 in. 304 mm
Quill travel: Z Vertical 5 in. 127 mm
Knee travel : Vertical 16 in. 406 mm
Ram Travel 12 in. 304.8 mm
Spindle Center to Column 6.75 - 18.5 in. 171mm- 470mm 171 - 470 mm
Spindle Nose to Table Top 2.125 - 18 in. 3.1 - 457 mm

Head, Spindle Inch Metric
Spindle Nose Taper R-8 R-8
Spindle Variable Speed Range 65-4500 rpm 65-4500 rpm
Spindle Motor (220V/440V) 11 HP 11HP

Quill Feed (Inch/Rev)(3 speeds)
.0015, .003, .006 in. .038, .076, .152 mm
Quill Diameter 3.375 in. 85.7 mm
Head Swivel Angle 360°
Head Tilt Angle (L/R) 45°
Head Tilt Angle (Up/Down) 45°

General

Inch Metric
Floor Area (W x D x H) 7 x 6.5 x 6.75 ft. 2.1 x 2 x 2 M
Approximate Weight 2,100 lbs. 952 Kg.
Power Consumption (220V) 3 KVA/15 amps
Power Consumption (440V) 3 KVA/8 amps
Single Phase 3 KVA/25amps

SERVO MOTOR DRIVE
The R-8 spindle is driven by a servo motor, providing a speed range of 65 to
4,500 rpm.
An 8.5kW spindle motor that is equivalent to an 11HP drive, which will
increase productivity via larger depths of cuts in milling, drilling, boring, and
tapping applications.
Fewer working parts to maintain by eliminating High/Low transmission gears,
so the mill is easier to operate, and extends the life of the machine.
Adjusts the speed and torque dynamically, allowing it to run quieter and with
less vibration than traditional variable speed drive mills for improved surface
finish and extended tool life.
Comes with a digital display, and the speed change is controlled by turning a
dial to the desired speed.
Comes standard with a load meter, which provides real-time monitoring of
spindle power usage, offering several benefits like preventing tool breakage,
improving cutting conditions, and optimizing machine performance
High Performance in Intermittent Use - Servo motors are ideal for
applications with start-stop operations. They can ramp up and down quickly
without consuming excessive energy.
Low Energy Loss - Servo motors are designed to minimize energy loss due to
heat and friction, contributing to theiroverall efficiency.
The mill comes equipped with a transformer located in the electrical control
cabinet which conveniently provides 110V power to DRO or X, Y, Z-Knee
power feeds.

STANDARD EQUIPMENT:
• Hard-Chrome Ways and Gibbs
• Precision Ground and Flaked Table
• Unique Double Nut Backlash System
• Cutler Hammer On/Off Switch
• Front And Rear Way Covers
• One Shot Lube System (X, Y, Z Axes)
• Tool Kit Includes:
Machine Manual, Half Nut Wrench, Wrench 17m, 19m, Set Of 6 Allen Wrenches, Philip Screwdriver, Flat Head Screwdriver, Oil Can, Grease Gun, Rear Way Cover Bracket, Pin for Indicator, Can of Paint.
• Wired 220V or 440V. Please Specify. (Note: 440V requires an additional transformer; 220V single phase is available)

OPTIONAL ACCESSORIES:

• 6” “Kurt” Vise with Swivel Base (DX6 vise & D50-4-SA swivel base)
5000-2126 A $ 1,558.00
• Auto lube pump Auto Lube2 $ 1,028.00
• Right Angle Milling Attachment with Arbor ACC-10-NT30 $ 2,406.00
• Right Angle Milling Attachment with Arbor ACC-10LMV-R8 $ 2,406.00
• “Sharp” Power Table Feed with Safety Handle (X-Axis)
* SP-250A (see notes) $ 981.00
“Sharp” Power Cross Feed with Safety Handle (Y-Axis) SP-250B $ 981.00
“Sharp” Power Knee Feed with Safety Handle (Z-Axis) SP-250D $ 981.00
X-Axis Installation $ 185.00 NET
Y-Axis Installation $ 300.00 NET
Z Axis Installation $ 300.00 NET
* NOTES: SP-250A installation may reduce the X-axis travel.

• Drill Chuck & Drill Arbor LMV-D/A $ 594.00
• 6” Riser Block ACC-26 $ 1,325.00
Riser Block Installation $ 210.00 NET
• Coolant System with Chip Pan at Base (pump included) C311-LMV$ 1,028.00
• “Maxi Torque Rite” Power Draw Bar TR-100 $ 1,102.00
Factory Installation $ 215.00 NET
• R-8 Collet (Set of 11) - 1/8”-3/4” BY 1/16” ACC-R8 $ 297.00
• Clamping Kit (52 pcs/Steel Rack) CK-104 $ 286.00
• Halogen Work light WL-110V55W $ 297.00
• CE mark NET $ 1,839.00
• UL (to meet the state of California) - components upgrade (factory order)
LMV-UL $ 4,040.00
• UL compliance certificate under the State of California
NET $ 4,725.00
• NFPA 79 parts upgrade NET $ 4,040.00
• 440V / 380V and 575 V transformer 440T4 NET $ 1,230.00
• Upgrade X/Y axis with ball screw (factory order) $ 4,500.00

DIGITAL READOUT SYSTEMS:
• Fagor Digital Readout
2-Axis X&Y (Fagor 20i) FG-LMV50 $ 2,200.00
3-Axis X&Y on Quill (Z) (Fagor 30i) FG-LMV50-3A $ 2,963.00
3-Axis X&Y on Knee (Z) (Fagor 30i) FG-LMV50-3AK $ 3,095.00

2 Axis D.R.O. Installation $ 510.00 NET
3 Axis D.R.O. Installation $ 845.00 NET

• Acu-Rite 203S Digital Readout
2-Axis X&Y AR-LMV50 $ 3,725.00
3-Axis X&Y on Quill (Z) AR-LMV50-3A $ 4,186.00
3-Axis X&Y on Knee (Z) AR-LMV50-3AK $ 5,271.00
4 – Axis X/Y/Quill/Knee (Z) 300 S AR-LMV50-4AK P.O.R

2- Axis D.R.O. Installation $ Net 510.00
3- Axis D.R.O. Installation $ Net 845.00
4- Axis DRO installation P.O.R

• Newall NMS 800 DRO
2-Axis X&Y NWN-LMV50 $ 2,300.00
3-Axis X&Y on Quill (Z) NWN-LMV50-3A $ 3,132.00
3-Axis X&Y on Knee (Z) NWN-LMV50-3AK $ 3,132.00

2 Axis D.R.O. Installation $ 510.00 NET
3 Axis D.R.O. Installation $ 845.00 NET