NEW 2025 SHARP LMV-49-DVS

SHARP DVS Pkg Variable Speed Vertical Knee Mill Model LMV-49K Travel 12" x 36.6" Table 9" x 49"
STANDARD EQUIPMENT:
3HP Motor
• Digital Variable Speed Drive
• R-8 Spindle
• Meehanite Casting
• Chromed Ways
• Self-Lubricating Motor Shaft Extends Pulley Life
• Abec-7 Super Precision Spindle Bearings
Power Feed Table
3 Axes Digital Readout System
• Hard-Chrome Ways And Gibbs
• Precision Ground And Flaked Table
• Unique Double Nut Backlash System
• Cutler Hammer On/Off Switch
• Front And Rear Way Covers
• One Shot Lube System (X , Y , Z Axes)
• Tool Kit Includes:
Machine Manual, Half Nut Wrench, Wrench 17m, 19m, Set Of 6 Allen Wrenches, Philip Screw Driver, Flat Head Screw Driver, Oil Can, Grease Gun, Rear Way Cover Bracket, Pin For Indicator, Can Of Paint
• Wired 220V or 440V. Please Specify. (Note: 440V requires additional transformer, 220 V single phase is available)

SPECIFICATIONS
Table
Working Surface 9” x 49”
T-Slots Number and Size 3 Slots, 5/8”
Capacity
Travels (X, Y, And Z) 36.6” x 12” x 5”
Ram Travel 12”
Knee Travel 16”
Spindle To Column (Min-Max) 6-3/4”-18 1/2”
Spindle Nose To Table (Min-Max) 2-1/8”-18”
Spindle
Spindle Motor 3 HP
Spindle Nose Taper R8
Digital Variable Speed Drive ( DVS) 65- 4500 RPM
Quill Feed 3 Speed (IPR) 0.0015,0.003, 0.006”
Head Swivels 360°
Head Tilt (Lt. To Rt) 45°
Head Tilt (Up And Down) 45°

SHARP LMV-49K-DVS PACKAGE VERTICAL MILL
WITH
3-AXIS DIGITAL READOUT (quill, saddle, table)
DIGITAL VARIABLE HEAD (DVS)
TABLE POWER FEED

TABLE
Working surface 9” x 49"
T-slot number, size 3, 5/8"

CAPACITY
Table travel (X,Y,Z) 36.6" x 12" x 5"
Ram travel 12"
Knee travel 16"
Spindle to column (min-max) 6 3/4" - 18-1/2"
Spindle to nose table 2 1/8” - 18"

SPINDLE
Motor 3 HP
Spindle Nose Taper R-8
Digital Variable Speed 60 ~ 4,500 RPM
Quill feed (IPR) 0.0015”, 0.003”, 0.006"
Head swivel 360º
Head tilt; right-to-left (each way) 45º
Head tilt up-and-down (each way) 45º

STANDARD EQUIPMENT:
• Hard-Chrome Ways and Gibbs
• Precision Ground and Flaked Table
• Unique Double Nut Backlash System
• Cutler Hammer On/Off Switch
• Front And Rear Way Covers
• One Shot Lube System (X, Y, Z Axes)
• Tool Kit Includes:
Machine Manual, Half Nut Wrench, Wrench 17m, 19m, Set Of 6 Allen Wrenches, Philip Screwdriver, Flat Head Screwdriver, Oil Can, Grease Gun, Rear Way Cover Bracket, Pin for Indicator, Can of Paint.
• Wired 220V or 440V. Please Specify. (Note: 440V requires an additional transformer; 220V single phase is available)

FEATURES:

• 3HP Motor
• Digital Variable Speed Drive
• R-8 Spindle
• Meehanite Casting
• Chromed Ways
• Self-Lubricating Motor Shaft Extends Pulley Life
• Abec-7 Super Precision Spindle Bearings
Power Feed Table
3 Axes Digital Readout System

OPTIONAL ACCESSORIES:
440 V Transformer - 3HP
Auto Lube Pump w/ 2 adjustments
6" Kurt Vise with Swivel Base D688
Right Angle Milling Attachment with Arbor
Drill Chuck & Drill Arbor
Coolant system with chip pan
Maxi Torque Rite Power Draw Bar
Riser block (4”, 7”)
R-8 Collet Set of 11 (1/8"-3/4" by 1/16")
Clamping Kit
Halogen work light
Spare Kit

Features, Function, & Benefits:
ISO 9002 Certified:
Quality Up To World Industry Standards.
Meehanite Casting:
Highest Grade Of Casting Possible.
A Pair Of Precision ABEC-7 Angular Contact Bearings To Support Spindle. The Quill Is Ground And Chromed To Fit The Housing:
This Insures A Spindle Run out Of .0004” T.I.R.
Motor Shaft And Varidrive Pulleys Are Dynamically Balanced, Then Chromed For A Flawless Fit, Ground Ribs On Inside Diameter:
For Smooth Speed Changes.
Motor Shaft Has An Oil Channel In The Center That Is Fed By A Grease Fitting On The Lower End:
To Keep Vari-Drive Pulley Moving Smoothly On The Shaft.
This LMV-49DVS Mill Uses A Roller Bearing For The Lower Support Of The Shaft
It Ensures Proper Loading, Support And Alignment It Also Prevents The Shaft From Being Distorted By The Tension Of The Belt:
For Quiet, Accurate Operation At Any Speed For Years And Years.
One Shot Lubrication System:
For Lubrication Of Ways And Lead Screws. (X,Y And Z-Axis)
Hand Scraped Saddle And Knee:
For Better Oil Retention. It Avoids Having Chips And Dirt Embed In The Knee And Damage The Sliding Surface.
Oil Groove Are Milled:
For Maximum Lubrication On All Wear Areas.
Table And Saddle Backlash Is Controlled By Double Nut Design:
Keeps Lead Screw In Contact With Bronze Nuts An All Times To Keep Backlash At .0008” Within 20”.
Table And Saddle Are Mounted With Thrust Bearings That Are Pre-Loaded:
Eliminating Endplay For Precisely Controlled Lateral Movement.
Patient Knuckle Design Uses 6 Bolt 3 Per Side, Securing Them From The Outside:
This Method Locks The Head Securely Resulting In Better Accuracy And Performance.

OPTIONAL ACCESSORIES:

• 6” “Kurt” Vise with Swivel Base (DX6 vise & D50-4-SA swivel base)
5000-2126 A $ 1,558.00
• Auto lube pump Auto Lube2 $ 1,028.00
• Right Angle Milling Attachment with Arbor ACC-10-NT30 $ 2,406.00
• Right Angle Milling Attachment with Arbor ACC-10LMV-R8 $ 2,406.00
• “Sharp” Power Table Feed with Safety Handle (X-Axis* SP-250 $ 981.00
“Sharp” Power Cross Feed with Safety Handle (Y-Axis) SP-250B $ 981.00
“Sharp” Power Knee Feed with Safety Handle (Z-Axis) SP-250D $ 981.00
X-Axis Installation $ 185.00 NET
Y-Axis Installation $ 300.00 NET
Z Axis Installation $ 300.00 NET
* NOTES: SP-250A installation may reduce the X-axis travel.

• Drill Chuck & Drill Arbor LMV-D/A $ 594.00
• 6” Riser Block ACC-26 $ 1,325.00
Riser Block Installation $ 210.00 NET
• Coolant System with Chip Pan at Base (pump included) C311-LMV $ 1,028.00
• “Maxi Torque Rite” Power Draw Bar TR-100 $ 1,102.00
Factory Installation $ 215.00 NET
• R-8 Collet (Set of 11) - 1/8”-3/4” BY 1/16” ACC-R8 $ 297.00
• Clamping Kit (52 pcs/Steel Rack) CK-104 $ 286.00
• Halogen Work light WL-110V55W $ 297.00
• CE mark NET $ 1,839.00
• UL (to meet the state of California) - components upgrade (factory order)
LMV-UL $ 4,040.00
• UL compliance certificate under the State of California NET $ 4,725.00
• NFPA 79 parts upgrade NET $ 4,040.00
• 440V / 380V and 575 V transformer 440T4 NET $ 1,230.00
• Upgrade X/Y axis with ball screw (factory order) $ 4,500.00

DIGITAL READOUT SYSTEMS:
• Fagor Digital Readout
2-Axis X&Y (Fagor 20i) FG-LMV50 $ 2,200.00
3-Axis X&Y on Quill (Z) (Fagor 30i) FG-LMV50-3A $ 2,963.00
3-Axis X&Y on Knee (Z) (Fagor 30i) FG-LMV50-3AK $ 3,095.00

2 Axis D.R.O. Installation $ 510.00 NET
3 Axis D.R.O. Installation $ 845.00 NET

• Acu-Rite 203S Digital Readout
2-Axis X&Y AR-LMV50 $ 3,725.00
3-Axis X&Y on Quill (Z) AR-LMV50-3A $ 4,186.00
3Axis X&Y on Knee (Z) AR-LMV50-3AK $ 5,271.00
4 – Axis X/Y/Quill/Knee (Z) 300 S AR-LMV50-4AK P.O.R

2 Axis D.R.O. Installation $ Net 510.00
3 Axis D.R.O. Installation $ Net 845.00
4 Axis DRO installation P.O.R

• Newall NMS 800 DRO
2-Axis X&Y NWN-LMV50 $ 2,300.00
3-Axis X&Y on Quill (Z) NWN-LMV50-3A $ 3,132.00
3-Axis X&Y on Knee (Z) NWN-LMV50-3AK $ 3,132.00

2 Axis D.R.O. Installation $ 510.00 NET
3 Axis D.R.O. Installation $ 845.00 NET