NEW PRECISION MATTHEWS MACHINERY CO PM-1660TL-V
Overview
PM-1440TL-V / PM-1640TL-V / PM-1660TL-V Main Features
Highest Quality Lathes, Made in TAIWAN
Large 2-1/2" Spindle Bore clear through spindle for through-headstock work (Actual dimension 2.55", will pass a 2-1/2" bar)
Uses 208-240V Single OR 3 Phase Power without modification - No converters needed for single phase operation
Variable Spindle Speeds from 30-2500 RPM, in 3 ranges (Low 30-145, Medium 105-5110, High 510-2500 RPM)
No change gears needed for the entire range of Inch and Metric thread pitches
Inch AND Metric thread cutting ability is a standard feature
True INCH PITCH main lead screw, cross feed, and compound lead screws make it easy to use for the INCH measurement System, yet still has the Metric readings on dials for the ultimate in versatility for any job that may come about
Power feed on Carriage and Cross Slide, both left and right, and in-and-out, for both turning and facing operations with automatic feed. Allows for the best surface finish in all directions.
Induction Hardened and Precision Ground Bed Ways to resist wear and give a long service life
Turcite B coating on carriage for extremely smooth operation and long life
All gears and shafts in headstock hardened and precision ground for long life, and precision ground for extremely quiet running
Meehanite Cast Iron used for rigidity and vibration dampening
Wide 10-1/4" bed provides more stability in heavier work
Removable Gap for larger diameter work
High quality electronics used throughout machine
Slip Clutch on feed rod, to help prevent overloading damage of feeds and allow the use of a solid micrometer carriage stop for repetitive work
High Precision Tapered Roller Bearings used in spindle, for the ultimate in long life, high precision, and best surface finishes. Guaranteed Run Out +/- .0001" for ultimate precision
One shot lubrication pump on carriage for easier lubrication and longer life
Only Extremely High Precision Japanese Spindle Bearings are used
Locking Tang in tail stock
Longest in the industry, 5 Year Warranty!
PM-1440TL/PM-1640TL/PM-1660TL Standard Accessories
High Precision 9” 3 Jaw Chuck, with Bolt On Jaws (can also use soft jaws)
D1-6 Camlock Spindle
2.55” (65mm) Spindle Bore
L.E.D. Work Light
Leveling Pads
Complete Cast Iron Base with slide out Chip Tray
High Precision (Japan) Spindle bearings, with +/- .0001" Max Spindle Runout
Back Splash Guard
Reducing Sleeve for Headstock Center
4 Way Tool Post
Headstock Dead Center
Tail Stock Dead Center
Thread Chasing Dial
Feed Rod Clutch (To prevent overloading and using carriage stops)
Everything Needed for listed Inch and Metric Thread Pitches
Steady Rest
Follow Rest
Coolant System
Foot Brake
5 Year Warranty
Specs
PM-1660TL-V
[Main Specifications]
Bed Width: 10.25 in
Distance Between Centers: 40" , 60"
Gap Insert Length: 10 in
Internal Taper: Internal MT4
Quill Tailstock Taper: MT4
Spindle Bore Diameter: 2.55"
Spindle Centerline to Floor: 47 in
Spindle Face to Tailstock Quill Face: 44" , 64"
Spindle Length: 24 in
Main (Threading) Leadscrew Pitch: 4 TPI
Quill Diameter: 2.047" (52mm)
Spindle Mount Type: D1-6 Camlock
Swing over bed: 14" , 16"
Swing Over Cross-slide: 8" , 10"
Swing Over Gap: 21" , 23"
Variant Base: Cast Iron Base
[Travels]
Compound Travel: 4.94 in
Cross-Slide Travel: 8.75 in
Quill Travel: 6 in
[Table]
[DRO Specifications]
[Power Requirements]
Amperage: 30
Voltage: 220V
Phase: Dual 1Φ or 3Φ
Power Frequency: 60Hz
Horsepower: 5
Plug supplied: Direct Wire, no wire or plug included
[Motor and Drive]
Motor Type: AC
Drive Type: Belt Drive
Speed Adjustment: Dual Stepped and Variable
Spindle Minimum Speed: 30
Spindle Maximum Speed: 2,500
[Cutting Capacities]
Longitudinal Feed Rate Range: 0.002-0.067 IPR
Cross-slide Feed Rate Range: 0.001 -0.034 IPR
Inch Threads: Choice of 45, from 2-72 TPI
Metric Threads: Choice of 39, from 0.2-14 mm pitch
Diametral Pitch: Choice of 21, 8-44 DP
Module Pitch: Choice of 18, 0.3-3.5 MP
[Unit Dimensions]
Unit Length: 90 in , 110 in
Unit Width: 41 in , 42 in , 44 in
Unit Height: 72 in , 74 in
Unit Weight: 3600 lb , 4000 lb , 4500 lb
[Shipping Information]
Shipping Length: 90 in , 110 in
Shipping Width: 41 in , 42 in , 44 in
Shipping Height: 72 in , 74 in
Shipping Weight: 3600 lb , 4000 lb , 4500 lb
Shipping Class: SC-F55E , SC-B60E
Liftgate Eligible: No
HS Code: 8458.19
Country of Origin: Taiwan
[Machine Footprint]
Footprint Depth: 36 in
Footprint Width X-Axis: 109 in
Compound (top slide) width (Where tool post sits, for tool post sizing) 3.937" (100mm)
Leveling bolt thread/size: M16x2.0, 70mm long
Explore More New Equipment Listings on Equipt
Browse related New Precision Lathes, Lathes & Turning Machines, Metal Cutting, and Metalworking equipment, including PRECISION MATTHEWS MACHINERY CO machines for sale on Equipt.
New Equipment for Sale in Pennsylvania, United States
Find New Precision Lathes, Lathes & Turning Machines, Metal Cutting, and PRECISION MATTHEWS MACHINERY CO equipment for sale in Pennsylvania, United States, with related local Metalworking searches.
New Equipment for Sale in United States
Browse New Precision Lathes, Lathes & Turning Machines, Metal Cutting, and PRECISION MATTHEWS MACHINERY CO equipment for sale across United States, including related Metalworking inventory paths.
Sell Your Used Equipment
Find dedicated pages to sell used Precision Lathes, Lathes & Turning Machines, Metal Cutting, Metalworking, and PRECISION MATTHEWS MACHINERY CO equipment on Equipt.