NEW PRECISION MATTHEWS MACHINERY CO PM-1340GT-1PH
Overview
PM-1340GT Main Features
Highest Quality Lathe, Made in TAIWAN
Large 1-9/16” Spindle Bore clear through spindle for through-headstock work
Short Spindle Length, only 13-3/4", perfect for gunsmithing work
Extra thick spindle wall for extra rigidity, almost double when compared with most other machines in this size
Power feed on Carriage, and Cross Slide, both left and right, and in and out, for both turning and facing operations with automatic feed. Allows for the best surface finish in all directions.
Induction Hardened and Precision Ground Bed Ways to resist wear and give a long service life
All shafts in headstock hardened and ground along with gears which are precision ground, set in with a close tolerance fit, which leads to longer life and quiet running when compared with other geared head lathes
Inch AND Metric thread cutting ability is a standard feature, NO CHANGE GEARS for any inch thread or feed rate, only change gears required are for Metric threads
4” Travel Thread Dial, 32 tooth gear on thread dial, 8 TPI Main Leadscrew for easier threading using the half nut / thread dial
Large diameter, extra thick wall tail stock quill for more rigid and accurate tail stock operations
Locking Tang in tail stock
Removable Gap for larger diameter work when needed
High quality electronics used throughout machine, very reliable contactors, motors, etc.
Slip Clutch is standard on feed rod, to help prevent overloading damage of feeds and allow the use of a solid carriage stop for repetitive work
Precision Tapered Roller Bearings used in spindle, for the ultimate in long life, high precision, and best surface finishes. Guaranteed Run Out +/- .0001" for ultimate precision
True INCH PITCH main lead screw, cross feed, and compound lead screws make it easy to use for the INCH measurement System, yet still has the Metric readings on dials for the ultimate in versatility for any job that may come about
Splash oil bath lubrication in Headstock and Apron, for efficient lubrication and long life, yet simple and reliable, and does not require any filter changes or pump maintenance as with oil pump lubrication systems. Also, no risk of losing oil flow to expensive parts as there can be with pump lubricated systems
Only Extremely High Precision Spindle Bearings are used, NACHI (Japan)
Longest in class, 5 Year Warranty
PM-1340GT Standard Accessories
(Machine is available in either single or 3 phase, select from drop down when ordering)
Back Splash Guard
L.E.D. Work Light
High Precision NSK Spindle Bearings, +/‐ .0001” Spindle Runout Max
4 Way Tool Post
Threading Dial (4” Travel Dial, 32 Tooth)
Reducing Sleeve for headstock
Dead Center for Headstock
Steady Rest
Dead Center for Tailstock
Follow Rest
Feed Rod Clutch
Chip Tray
Misc. Tools for operation
D1‐4 Camlock Quick Change Spindle
Belt Cover Interlock Switch
D1-4 Face Plate (10")
5 Year Warranty
*Note, chucks are not included standard, please select chuck option from the optional accessories if you need a chuck with your machine
Specs
PM-1340GT-1PH
[Main Specifications]
Feed Rod Diameter: 0.75"
Bed Height: 11.5"
Bed Length: 63.75 in
Bed Width: 7.5 in
Distance Between Centers: 40"
Follow Rest Capacity: 1.5 in
Gap Insert Length: 7.75 in
Internal Taper: Internal MT5
Quill Tailstock Taper: MT3
Spindle Bore Diameter: 1.5625"
Spindle Centerline to Floor: 46 in
Spindle Face to Gap End: 5.5 in
Spindle Face to Tailstock Quill Face: 40 in
Spindle Length: 13.75 in
Spindle Length to Typical Chuck Face: 17.25 in
Steady Rest Capacity: 2.5 in
Swing over bed: 13 in
Swing over cross-slide: 6.5 in
Swing over gap: 19.13 in
Main (Threading) Leadscrew Pitch: 8 TPI
Main Leadscrew Diameter: 0.875"
Quill Diameter: 1.5625"
Spindle Mount Type: D1-4 Camlock
[Travels]
Compound Travel: 3.5 in
Cross-Slide Travel: 6.75 in
Quill Travel: 4 in
[Table]
[DRO Specifications]
[Power Requirements]
Amperage: 20
Voltage: 220V
Phase: 1PH , 3PH
Power Frequency: 60Hz
Horsepower: 2
Plug supplied: Direct Wire, no wire or plug included
[Motor and Drive]
Motor Type: AC
Drive Type: Gear Linkage
Speed Adjustment: Stepped
Spindle Minimum Speed: 90
Spindle Maximum Speed: 1,800
Spindle Speeds: 90, 135, 205, 205, 308, 475, 335, 505, 770, 780, 1160, 1800
[Cutting Capacities]
Longitudinal Feed Rate Range: 0.002-0.02 IPR
Cross-slide Feed Rate Range: 0.001-0.01 IPR
Inch Threads: Choice of 40, 4-112 TPI
Metric Threads: Choice of 24, 0.25-7.5mm pitch
[Unit Dimensions]
Unit Length: 69.25 in
Unit Width: 30 in
Unit Height: 30 in
Unit Weight: 1100 lb
[Shipping Information]
Shipping Length: 72 in
Shipping Width: 32 in
Shipping Height: 36 in
Shipping Weight: 960 lb
Liftgate Eligible: Yes
HS Code: 8458.19
Country of Origin: Taiwan
[Machine Footprint]
Footprint Depth: 69.25 in
Footprint Width X-Axis: 22 in
Footprint Height: 48.5 in
Explore More New Equipment Listings on Equipt
Browse related New Engine Lathes, Lathes & Turning Machines, Metal Cutting, and Metalworking equipment, including PRECISION MATTHEWS MACHINERY CO machines for sale on Equipt.
New Equipment for Sale in Pennsylvania, United States
Find New Engine Lathes, Lathes & Turning Machines, Metal Cutting, and PRECISION MATTHEWS MACHINERY CO equipment for sale in Pennsylvania, United States, with related local Metalworking searches.
New Equipment for Sale in United States
Browse New Engine Lathes, Lathes & Turning Machines, Metal Cutting, and PRECISION MATTHEWS MACHINERY CO equipment for sale across United States, including related Metalworking inventory paths.
Sell Your Used Equipment
Find dedicated pages to sell used Engine Lathes, Lathes & Turning Machines, Metal Cutting, Metalworking, and PRECISION MATTHEWS MACHINERY CO equipment on Equipt.