USED 1975 HUNTER COIL COATING LINE

60" Aluminum Can-End Coating Line: CC-157
- Single coat line for light gauge aluminum coatings/finishes.
- Sold "as is, where is" EXW on foundation USA.

Strip Width: - 60" max / 1524 mm - 66" w/o tension leveling section

Entry Coil Size: - ID - 20" (508 mm) / OD - ? / Weight - 50,000 lbs (27.2 mtons)
Exit Coil Size: - ID - 16" (406 mm) / OD - 70" max (1778 mm) / Weight - 48,000 lbs (21.8 mtons)

Manufacture:
- Hunter and GFG
- New in 1975
- Reinstalled 1984 with upgrades

Design: Single coat line

Line Speed:
- Rated: 275 fpm / 84 mpm
- Actual ran: 300 fpm / 91.4 mpm

Strip Thickness:
- .008 - .020" / 0.20 - 0.51mm

Strip Width:
- 60" max / 1524 mm
- 66" w/o tension leveling section

Entry Coil Size:
- ID - 20" / 508mm
- OD - ?
- Wt. - 50,000 lbs / 11.34 mtons

Exit Coil Size:
- ID - 16" / 406mm
- OD - 70" max / 1778mm
- Wt - 48,000 lbs / 10.89 mtons

Uncoiler #1:
- 80 hp, 800/1500 rpm, 15.983:1 gear ratio

Coil Car #1:
- Above ground, 50,000 lbs

Scrap Winder:
- Mandrel type with scrap car

Uncoiler #2:
- 80 hp, 800/1500 rpm, 15.983:1 gear ratio

Coil Car #2
- Above ground, 50,000 lbs

Pinch Roll

Crop Shear

Strip Joiner:
- Behlen, Single die

Bridle 1 of 7

Entry Accumulator:
- 9 rolls over 8
- 12.8" diam rolls
- 60 seconds of strip storage at 300 fpm

Bridle 2 of 7

Tension Leveler:
- 60" max strip width
- Entry Bridle (Line bridle #3)(2 roll unit)
- Roll 1 - 25 hp, 1750/2500 rpm, 34.13:1 gear ratio
- Roll 2 - 50 hp, 1750/2500 rpm, 33.23:1 ratio
- BWG Flex-Roll Section:
- 5 roll cassettes
- Work rolls: 1.125" & 1.75" diam
- Back up Rolls: 2.25" diam
- Exit Bridle (Line bridle #4)(2 roll unit)
- Roll 3 - 150 hp, 1750/2500 rpm, 34.5:1 gear ratio
- Roll 4 - 75 hp, 1750/2500 rpm, 33.02:1 gear ratio

Bridle 5 of 7

Cleaning Section
- Stages 1-2 = vertical
- Stages 3-4-5 = horizontal
- Vertical Air blow off

Coater:
- GFG, 2 side coat
- Rolls: 10" diam x 72" face

Paint Flow-Out Booth - 15 ft long section

Oven:
- 90 ft long / 27.4 m
- 3-zone gas-fired catenary type
- Exit water quench
- Exit air quench

Bridle 6 of 7

Exit Accumulator:
- 9 rolls over 8
- 12.8" roll diameter
- 60 seconds of strip storage at 300 fpm

Bridle 7 of 7

Waxer:
- GFG
- 2-12 mg per sq ft laydown

Exit Shear

Exit Pinch Roll

Recoiler:
- 60 hp, 500/2000 rpm, 18.611:1 gear ratio
- Mandrel type
- With Belt wrapper, coil car, and downender

Sold "as is, where is" EXW foundation USA.

Price of this line is very low. BUT Buyer must pay for complete line dismantling including asbestos in the ovens and floor repair.